en:tinkering:laser:eleksmakera3pro
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
en:tinkering:laser:eleksmakera3pro [2020/10/20 14:51] alessio.cavalieri [Blog] |
en:tinkering:laser:eleksmakera3pro [2020/10/20 15:41] (current) alessio.cavalieri [Blog] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== EleksMaker EleksLaser-A3 Pro ====== | ====== EleksMaker EleksLaser-A3 Pro ====== | ||
| ===== Blog ===== | ===== Blog ===== | ||
| - | * 2020 october 20: added [[en:tinkering:laser:eleksmakera3pro#power_and_speed_settings|Power and speed settings section]] | + | * 2020 october 20: added [[en:tinkering:laser:eleksmakera3pro#power_and_speed_settings|Power and speed settings ]] section |
| * 2017 december 18: Improved the smoothness of the X carriage, $110=5000 and $111=5000 for setting the max speed to 5000 mm/min in GRBL | * 2017 december 18: Improved the smoothness of the X carriage, $110=5000 and $111=5000 for setting the max speed to 5000 mm/min in GRBL | ||
| * 2017 december 13: Added smoke blower and pimped up step drivers current, heat sink installed on Allegro chip | * 2017 december 13: Added smoke blower and pimped up step drivers current, heat sink installed on Allegro chip | ||
| Line 21: | Line 21: | ||
| ===== Power and speed settings ===== | ===== Power and speed settings ===== | ||
| ==== 2500 mW Laser Diode ==== | ==== 2500 mW Laser Diode ==== | ||
| - | ^ Job type ^ Material ^ Thickness ^ Example ^ | + | === Vector letters outline / thin outline === |
| - | | Vector letters outline / thin outline | Plywood | N/I | | | + | |
| + | ^ Material ^ Laser Power (%) ^ Passes ^ Cut rate (mm/min) ^ Example ^ | ||
| + | | Plywood | 20 | 1 | 500 | {{:en:tinkering:laser:2-5w_laser_vector_letters_outline_plywood_3mm.jpg?200|}} | | ||
| + | |||
| + | === Vector letters fill path === | ||
| + | ^ Material ^ Line Distance (mm) ^ Laser Power (%) ^ Passes ^ Cut rate (mm/min) ^ Example ^ | ||
| + | | Plywood | 0.1 | 20 | 1 | 1000 | {{:en:tinkering:laser:2-5w_laser_vector_letters_fill_path_plywood_3mm.jpg?200|}} | | ||
| + | |||
| + | === Cut === | ||
| + | ^ Material ^ Thickness (mm) ^ Laser Power (%) ^ Passes ^ Cut rate (mm/min) ^ Example ^ | ||
| + | | Plywood | 3 | 50 | 8 | 80 | {{:en:tinkering:laser:2-5w_laser_cut_plywood_3mm.jpg?200|}} | | ||
| ===== GRBL settings ===== | ===== GRBL settings ===== | ||
en/tinkering/laser/eleksmakera3pro.1603198290.txt.gz · Last modified: 2020/10/20 14:51 by alessio.cavalieri
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
